DIY

6 tips when using wood planer what you require to know

A wood planer is a powerful product used to assist workers in wood production and processing. It is the impact of the portable wood planer that enhances the value of the finished product, smoothing the surface for easier fabrication. Most wood planing devices are made of articulated shafts connected to the blade in a forward motion, which leads to that only one damaged part will make the other parts unable to work.

Some customers look at a wood planer and think it’s simple to use. But they are wrong. If you do not study and practice hard, you will not know how to use it correctly and effectively but also endanger you.

Therefore, here are 6 tips when using the best wood planer to ensure safety and make your wood planning process more efficient and accurate. Let’s find out!

Thickness Planner
Thickness Planner

Check the sharpness of the blade before you start using it

If you want good results in your productivity, the blade of your wood planer (also known as a knife) needs to be sharp and firm. You must check before each use. Because after each planing, the machine will be blunted quickly on the edges even if you just sharpened the day before.

In some cases, you can sharpen knives while they are still in the planer. In other cases, you will need to remove them from the machine and re-grind. Worst case, you have to replace the new one, if the blade is too blunt. Check your user manual for instructions.

Note: If you need to replace a knife, make sure you replace all of them at once. Because, if some are sharp and others are blunt, you will get an uneven wood shaving result.

And if you need to remove the knife to sharpen them, be careful not to remove too many other parts of the machine. Because it is difficult to reinstall in the correct position.

Make sure your Planner knife is aligned correctly

Most hand-held planers will use a pair of knives to scrape the wood. Accordingly, the reason is that if they are not aligned with each other, you will not achieve the best planing results. Therefore, check the balance of the blade before use to reach high productivity at work and avoid wasting time to readjust.

Always planing in the direction of the wood grain

Remember to always plan the wood in the same direction as the wood grain. It is easy to see how to do this but many users often forget. The grain is a series of lines on the surface of the wood. If you plan in the same direction as the wood grain, you will go straight and go very far. That helps you plan faster and more beautiful.

However, if you try to plan the wood, not in the direction of the wood grain, you will find that the machine is stuck. It will tear through the wooden board and leave an ugly, jagged edge that will damage the panel.

Note: However, there are exceptions. There are several types of wood with particles running in many directions. In those cases, you will need to work carefully and use a very sharp blade.

Thin passes repeatedly are better than deeper passes

Most planers allow you to adjust the depth into the wood.  For example, electric handheld planers often offer a variety of settings – called ‘active stops.” The maximum depth varies with each level.

As I observe, for thin planing, although there is a lot of small wood chips and longer process, it does not damage the panel. On the contrary, you want to do it faster by shaving once more deeply. It led to the wooden plane appears many large cuts extremely unattractive.

For both of these reasons, it’s much better to use iterations in shallower settings.

Always collect dust after use

Gathering dust when you are not using it will give you less resistance when you operate later. And that means less chance of slipping or tearing.

If you use a manual planer, this can be as simple as blowing away sawdust when you are with you. But if you already have a planer, you will have other options. Many handheld planers will come with their dust bag. However, these are usually small and need to be cleaned up regularly.

A better solution might be to connect the store’s vacuum cleaner to the planer’s dust exhaust. That will keep the wood dust moving out of the machine, and avoid any problems with congestion.

Use the right tools for the job

There are many different wood planers, and they will work better or worse for different functions. For instance, if you need to plan the edge of a table, you use the best thickness planer, which is not appropriate. It will ruin your desk. Therefore, please consider carefully the needs and purposes to choose the appropriate planing machine.

In conclusion

We hope you have enjoyed our top six tips for achieving great results when using a wood planer. Make sure your device is in good condition, and take time for proper preparation. Follow these suggestions, and you’ll save time and the funds for replacing damaged boards will be gone.

Leave a Comment